Programmable Constant Wet Constant Humidity / High And Low Temperature Chamber IEC68

Programmable Constant Wet Constant Humidity / High And Low Temperature Chamber IEC68

The test machine is mainly used for electronics, electrical, food, automobile, oak plastics, metal, parts and other products, transportation and materials in high and low temperature hot and humid environment; it is the reliability test equipment for electronics, electrical, electrical, plastic and pipe engineering.

Certification :
Calibration Certificate(cost additional)
Price :
Negotiable
Delivery Time :
30 days
Payment Terms :
L/C, T/T
Brand Name :
HCTE
Model Number :
HCTE0029

Inquiry now

Product Details

Programmable Constant Wet Constant Humidity / High And Low Temperature Chamber IEC68

Products Introduction:

The test machine is mainly used for electronics, electrical, food, automobile, oak plastics, metal, parts and other products, transportation and materials in high and low temperature hot and humid environment; it is the reliability test equipment for electronics, electrical, electrical, plastic and pipe engineering.

Application:

It is applicable to the cold, heat, moisture and dry resistance test of various electronic, electrical, electrical, plastic and other raw materials and devices and the reliability test equipment of quality control engineering.

Feature:

1.It is especially suitable for the high temperature resistance, low temperature resistance and humidity resistance cycle test of optical fiber, LCD, crystal, inductance, PCB, battery, computers, mobile phones, rubber, plastic and other products;

2.This machine can simulate different environmental conditions such as high temperature and high humidity / high temperature, low humidity / low temperature / high temperature / low temperature, with easy operation and learning of high accuracy programming control and fixed-point control system, to provide the best test environment.

Meet the standards:

GB-2423.1-2008 (IEC68-2-1) Test A: Low-temperature test method.

GB-2423.2-2008 (IEC68-2-2) Test B: High-temperature test method.

GJB360.8-2009(MIL-STD.202F) High-temperature life test.

GJBl50.3-2009 (M-I L-STD-810D).

GJBl50.4-2009 (MIL-STD-8 I 0 D).

GB2423.3-2008 (IEC68-2-3) Test Ca: constant heat and humidity test method.

GB2423.4-2008 (IEC68-2-30) Test Db: heat heat test method.

GJBl50.9-2009 (MIL-STD-810D) wet-heat test method.

Parameters:

Model	HCTE0029-HW-80	HCTE0029-HW-150	HCTE0029-HW-225	HCTE0029-HW-408	HCTE0029-HW-800	HCTE0029-HW-1000
Inner box size mm (W * H * D)	400×500×400	500×600×500	500×750×600	600×850×800	1000×1000×800	1000×1000×1000
Outer box size mm (W * H * D)	600×1650×1200	700×1760×1545	700×1910×1625	800×2010×1845	1200×2035×1850	1200×2035×2050
Temperature range	A:-20～+150℃ B:-40～+150℃ C:-70～+150℃
Humidity range	20%～98%RH
Temperature departure	±2℃
Temperature uniformity	±2℃
Temperature fluctuation	±0.5℃
Heating rate	Approximately 3℃ / min (nonlinear, no-load)
Cooling rate	Average 1.0℃ / min (non-linear, no-load)
Humidity deviation	±3.0％RH（＞75％RH）；±5.0％RH（≤75％RH）
Humidity uniformity	± 3.0%RH (no-load)
Humidity fluctuation	± 2.5%RH (no-load)
Internal box material	SUS304 stainless steel plate
Outer box material	A3 Cold-rolled steel sheet electrostatic double-sided injection molding / SUS304 stainless steel
Heat insulation material	Hard matter polyurethane foaming
Refrigeration method	Air-cooled type (using the French Taikang fully closed compressor)
Cryogen	R404a、R23
Temperature and humidity sensor	Class A PT100 Platinum resistance
Heater	Nickel-chromium alloy electric heating type heater
Humidifier	External humidification, U-type design plus overtemperature probe hole.
Supply source	220V±10%V/ 380V±10%V；50Hz；
Protection system	Power supply phase deficiency and phase sequence error protection, water shortage automatic alarm protection, leakage protection, heater overtemperature protection, heater short-circuit and other overcurrent protection
Installation environment	Temperature: 2℃ ~30℃; relative humidity: 85%; air pressure: 86kPA~106kPa
	The installation site shall be flat, well ventilated and no strong vibration around the equipment
	There is no strong electromagnetic field influence around the equipment, no flammable, explosive, corrosive substances and dust around the equipment.
	Proper use and maintenance space remains around the equipment

Hot Tags :

Leave a message

Polyester Powder Coating for industry or architectures

Subject : Programmable Constant Wet Constant Humidity / High And Low Temperature Chamber IEC68

Submit

Categories

how can we help you

You can contact us any way that is convenient for you. We are available 24/7 via email or telephone.

Related Products

Related Products

Xenon Lamp Weatherproof Test Chamber (Air-Cooled Type) ISO 105-B04:1994 ISO4892-2:2006

The test machine is mainly used for electronics, electrical, food, automobile, oak plastics, metal, parts and other products, transportation and materials in high and low temperature hot and humid environment; it is the reliability test equipment for electronics, electrical, electrical, plastic and pipe engineering.

View details